diff --git a/printer_data/config/macros/print_start.cfg b/printer_data/config/macros/print_start.cfg
index cc38661..fcb7624 100644
--- a/printer_data/config/macros/print_start.cfg
+++ b/printer_data/config/macros/print_start.cfg
@@ -24,6 +24,18 @@
 #     STATUS_HEATING
 #     M109 S{extrudertemp}
 
+
+#    STATUS_READY
+#    STATUS_OFF
+#    STATUS_BUSY
+#    STATUS_HEATING
+#    STATUS_LEVELING
+#    STATUS_HOMING
+#    STATUS_CLEANING
+#    STATUS_MESHING
+#    STATUS_CALIBRATING_Z
+
+
 [gcode_macro PRINT_START]
 gcode:
   {% set target_bed = params.BED|int %}
@@ -34,14 +46,6 @@ gcode:
 
   RESPOND PREFIX="PRINT_START: " MSG="Starting the print..."
 
-  # Home the printer, set absolute positioning and update the Stealthburner LEDs.
-  BED_MESH_CLEAR                                       # Clear old saved bed mesh (if any)
-  RESPOND PREFIX="PRINT_START: " MSG="Homing all axes"
-  LED_STATUS_HOMING                                     # Set LEDs to homing-mode
-  G28                                                   # Full home (XYZ)
-  G90                                                   # Absolute position
-
-
   # Check if the bed temp is higher than 90c - if so then trigger a heatsoak.
   {% if target_bed > 90 %}
     # TODO!
@@ -67,24 +71,34 @@ gcode:
     # G4 P300000                                          # Wait 5 min for the bedtemp to stabilize
   {% endif %}
 
-  # QGL & Meshing
+  #
+  # All the calibration bits: Homing & QGL & Meshing
+  #
   RESPOND PREFIX="PRINT_START: " MSG="Heating hotend (for calibration) to: 140c"
   LED_STATUS_HEATING                                    # Set LEDs to heating-mode
-  M109 S140                                             # Heat hotend to 150c
+  M109 S140                                             # Heat hotend to 140c
+
+  # Home the printer, set absolute positioning and update the Stealthburner LEDs.
+  BED_MESH_CLEAR                                       # Clear old saved bed mesh (if any)
+  RESPOND PREFIX="PRINT_START: " MSG="Homing all axes"
+  LED_STATUS_HOMING                                     # Set LEDs to homing-mode
+  G28                                                   # Full home (XYZ)
+  G90                                                   # Absolute position
 
   RESPOND PREFIX="PRINT_START: " MSG="Performing QGL"
-  LED_STATUS_LEVELING                                      # Set LEDs to leveling-mode
-  QUAD_GANTRY_LEVEL                                    # Level the printer via QGL
-  G28 Z                                                # Home Z again after QGL
+  LED_STATUS_LEVELING                                   # Set LEDs to leveling-mode
+  QUAD_GANTRY_LEVEL                                     # Level the printer via QGL
+  G28 Z                                                 # Home Z again after QGL
 
-  #SET_DISPLAY_TEXT MSG="Bed mesh"                      # Display info on display
-  #STATUS_MESHING                                       # Set LEDs to bed mesh-mode
-  #BED_MESH_CALIBRATE                                   # Start the bed mesh (add ADAPTIVE=1) for adaptive bed mesh
+  #RESPOND PREFIX="PRINT_START: " MSG="Creating bed mesh"   # Display info on display
+  #LED_STATUS_MESHING                                       # Set LEDs to bed mesh-mode
+  #BED_MESH_CALIBRATE                                       # Start the bed mesh (add ADAPTIVE=1) for adaptive bed mesh
+
+  G1 X{x_wait} Y{y_wait} Z20 F9000                      # Go to center of the bed
 
   # Heat to target temp
   RESPOND PREFIX="PRINT_START: " MSG="Heating hotend (for first layer) to: {target_extruder}c"
-  LED_STATUS_HEATING                                        # Set LEDs to heating-mode
-  G1 X{x_wait} Y{y_wait} Z15 F9000                      # Go to center of the bed
+  LED_STATUS_HEATING                                    # Set LEDs to heating-mode
   M107                                                  # Turn off partcooling fan
   M109 S{target_extruder}                               # Heat the hotend to set temp