From fea4003a1d8c64d5acde18215ca787919165989d Mon Sep 17 00:00:00 2001
From: macocha <m@tooinconsistent.com>
Date: Sun, 6 Jul 2025 14:51:57 +0000
Subject: [PATCH] print_start.cfg modified - 07/06/2025 - 02:51:54 PM

---
 printer_data/config/macros/print_start.cfg | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/printer_data/config/macros/print_start.cfg b/printer_data/config/macros/print_start.cfg
index 68730b8..084f580 100644
--- a/printer_data/config/macros/print_start.cfg
+++ b/printer_data/config/macros/print_start.cfg
@@ -27,7 +27,7 @@ gcode:
   # If the bed temp is not over 90c, then skip the heatsoak and just heat up to set temp with a 5 min soak
   {% else %}
     RESPOND PREFIX="PRINT_START: " MSG="Heating bed to: {target_bed}c"
-    LED_STATUS_HEATING                                    # Set LEDs to heating-mode
+    LEDS_STATUS_HEATING                                    # Set LEDs to heating-mode
     G1 X{x_wait} Y{y_wait} Z15 F9000                      # Go to center of the bed
     M190 S{target_bed}                                    # Set the target temp for the bed
     # SET_DISPLAY_TEXT MSG="Soak for 5 min"               # Display info on display
@@ -38,23 +38,23 @@ gcode:
   # All the calibration bits: Homing & QGL & Meshing
   #
   RESPOND PREFIX="PRINT_START: " MSG="Heating hotend (for calibration) to: 140c"
-  LED_STATUS_HEATING                                    # Set LEDs to heating-mode
+  LEDS_STATUS_HEATING                                    # Set LEDs to heating-mode
   M109 S140                                             # Heat hotend to 140c
 
   # Home the printer, set absolute positioning and update the Stealthburner LEDs.
   BED_MESH_CLEAR                                       # Clear old saved bed mesh (if any)
   RESPOND PREFIX="PRINT_START: " MSG="Homing all axes"
-  LED_STATUS_HOMING                                     # Set LEDs to homing-mode
+  LEDS_STATUS_HOMING                                     # Set LEDs to homing-mode
   G28                                                   # Full home (XYZ)
   G90                                                   # Absolute position
 
   RESPOND PREFIX="PRINT_START: " MSG="Performing QGL"
-  LED_STATUS_LEVELING                                   # Set LEDs to leveling-mode
+  LEDS_STATUS_LEVELING                                   # Set LEDs to leveling-mode
   QUAD_GANTRY_LEVEL                                     # Level the printer via QGL
   G28 Z                                                 # Home Z again after QGL
 
   RESPOND PREFIX="PRINT_START: " MSG="Creating bed mesh"   # Display info on display
-  LED_STATUS_MESHING                                       # Set LEDs to bed mesh-mode
+  LEDS_STATUS_MESHING                                       # Set LEDs to bed mesh-mode
   BED_MESH_CALIBRATE                                       # Start the bed mesh (add ADAPTIVE=1) for adaptive bed mesh
 
   RESPOND PREFIX="PRINT_START: " MSG="Smart parking the nozzle"
@@ -62,13 +62,13 @@ gcode:
 
   # Heat to target temp
   RESPOND PREFIX="PRINT_START: " MSG="Heating hotend (for first layer) to: {target_extruder}c"
-  LED_STATUS_HEATING                                    # Set LEDs to heating-mode
+  LEDS_STATUS_HEATING                                    # Set LEDs to heating-mode
   M107                                                  # Turn off partcooling fan
   M109 S{target_extruder}                               # Heat the hotend to set temp
   
   RESPOND PREFIX="PRINT_START: " MSG="Purging nozzle"
-  LED_STATUS_PRINTING
+  LEDS_STATUS_PRINTING
   VORON_PURGE
 
   RESPOND PREFIX="PRINT_START: " MSG="Starting the print..."
-  LED_STATUS_PRINTING
\ No newline at end of file
+  LEDS_STATUS_PRINTING
\ No newline at end of file